contact seal
英 [ˈkɒntækt siːl]
美 [ˈkɑːntækt siːl]
网络 接触密封; 接触式密封
双语例句
- This fact does not contact the shaft seal surface, it is the sealing principle of polymer cooled to half molten state and forming the seal.
这种密封实际上并不接触轴的表面，它的密封原理是将聚合物冷却到半熔融状态而形成自密封。 - The author introduced installation technology and skill with the examples of axial labyrinth seal and radial contact seal.
作者以轴向迷宫式密封和径向接触式密封为例，介绍了安装技巧和要点。 - And the extension units at both ends of the sliding contact surface Guide to seal well, absolutely rigid Coarse prevent the entry of foreign matter sliding surface damage Guide.
大拖板与滑动导轨接触的两端面要密封好，绝对防止硬质颗粒状的异物进入滑动面损伤导轨。 - Reliability Design of a Contact Type Flexible Seal for Rotary Air Preheaters
回转式空气预热器接触式柔性密封可靠性设计 - If yes, please provide name, detailed address and contact details with reason and company seal or authorized signature on separate sheet.
如果是，请另备纸张写上公司名称、详细地址及联络人资料，并另说明理由及盖上公章或签名。 - With the increase of the difference in lip and shaft diameter, the maximum contact pressure has a trend of increase by degrees, the increscent scope of the small oil seal are more remarkable.
增大唇部过盈量，最大接触压力也随之而呈递增趋势，同样小尺寸油封递增幅度要大于大尺寸油封。 - Apply a light film of engine oil on the vibration damper hub contact surface of the seal.
在减震器毂油封接触表面上涂一层引擎机油薄膜。 - Contact Seal and Selection of Slot Type for Inner Ring of Ball Bearing
球轴承内圈接触密封及槽形选择 - The effect of axial dimension on the hysteresis and contact pressure of the finger seal mechanism is analyzed by the adoption of contact models with FEM ( Finite Element Method).
采用有限元接触模型分析了指尖密封片轴向尺度对指尖密封的迟滞特性及接触压力的影响。 - However, the contact phenomena are very complex, because it is not only related with the large deformation of seal, but also related with the position and direction of contact point of the door and the frictional behavior of the door and the seal.
然而密封条与车门之间的接触问题非常复杂，它不仅与密封条的大变形有关，而且与车门的接触点的位置与方向、摩擦特性等有关。 - Therefore, the contact algorithm is established based on direct restriction and the contact characteristics between the seal and the door are studied using numerical method.
为此，笔者建立了基于直接约束法的接触算法，利用数值方法对密封条与车门之间的接触特性进行了分析研究。 - The seal and friction wear efficiency of the drilling pump piston mainly depended on the contact stress description between the rubber seal ring and the inside hole of cylinder, so the research of contact stress has a realistic and important meaning.
活塞的密封性及摩擦磨损等性能都主要和活塞皮碗与缸套内壁间所形成的接触应力有关，因此，接触应力分布规律的研究具有重要的实际意义。 - The maximum contact pressure is decreased with the increase of the R value, and the change of R value has more remarkable influence on the maximum contact pressure of the small dimension oil seal.
最大接触压力随R值的增大而逐渐减小，且R值的改变对于小尺寸油封最大接触压力的影响较大； - Based on the contact-face penalty function method, bimetal face seal is digitally simulated and analyzed by FEM.
本文利用基于接触面的罚函数算法，通过有限元数值计算方法对双金属密封结构进行了数值模拟分析。 - Monitoring Technique of Contact Degree between Mechanical Seal Faces
机械密封端面接触状态测控技术 - In the course of commissioning tests of the unit there emerged a series of problems, such as a physical contact and rub of seal pads, vibration fluctuations and excessively large hypercritical vibrations.
在调试期间出现了密封瓦碰磨、振动波动、过临界振动大等问题。 - Study on contact characteristics between seal and door based on direct restriction
基于直接约束法的密封条与车门之间的接触特性研究 - Finite Element Analysis of Contact Pressure on Lip of the Oil Seal
油封唇口压力大小及分布的有限元分析 - A new type non-contact mechanical seal system, namely, dry gas seal was introduced, including the working principle and applying characteristics of it. Conditions and scope for application of dry gas seal were presented.
介绍了新型的非接触机械密封系统即十气密封，包括了干气密封的工作原理和应用特点，简要地给出了其使用条件、范围。 - Technical Study on Design of Spring Force for Contact-type Mechanical Seal
接触式机械密封弹簧力设计技术研究 - Results show that normal contact stress is critical to assure a safety seal, which increases with the increase of the pneumatic pressure and axial diameter.
结果表明，法向接触应力是实现有效密封的关键，该应力随充气压力和轴径的增大而增大； - It is well known the geometric structure of the rough surface influences numerous physical properties of the machine part, as friction, wear, lubrication, contact stiffness, seal, contact resistance and so forth.
众所周知，零件粗糙表面的几何结构影响着零件的众多物理性能，如摩擦、磨损、润滑、接触强度、密封性、接触电阻等等。 - Based on Ansys FEM method, the Influences of the axial dimensional disposition of sealing pieces in the axial arrangement, under the conditions of different pressure differentials, on the hysteresis and contact pressure of finger seal mechanism have been studied in the current work.
采用有限元技术研究了在不同压差条件下，指尖密封轴向布局中密封件轴向尺度配置对指尖密封装置的迟滞特性、密封靴与转子接触封严区接触压力的影响。 - Design Practice of Metallic Contact Seal of Piston Ring Type
金属涨圈接触式密封设计实践 - Marc. The seal mechanism was analyzed and normal contact stress distribution along seal bead was obtained.
Marc，考虑结构的材料非线性、几何非线性和接触非线性，建立了充气式气囊密封的轴对称有限元模型，对其充气密封机制进行了分析，得到了唇口法向接触应力的分布规律； - A sort of new dry gas seal can shorten or avoid the time of contact in seal starting up process was put forward as a solution.
针对此提出研究一种能减小或消除启动过程中端面接触时间的新型密封。 - Contact analysis of seal ring on new pressure vessel flanges
新型压力容器法兰密封结构的有限元接触分析 - Contact state of end face brush seal was analyzed by ANSYS.
采用ANSYS软件分析了端面刷式密封的接触状态。 - The conception of critical contact pressure and maximum seal pressure difference were defined.
定义了临界接触压力和最大密封压差的概念。